PAGlink 94Wh 14.8V Linking Batteries with Free PowerHub

Buy (6) PAGlink HC-PL-94T 94Wh 14.8V Linking Batteries by November 30, 2017 and receive a PAGlink PowerHub at no charge.

Includes:

• 6x PAGlink HC-PL-94T 94Wh 14.8V Linking Batteries - Gold Mount
• 1x PAGlink PowerHub - Gold Mount

PAGlink HC-PL94T 94Wh 14.8V High-Power Linking Battery - Gold Mount

The PAGlink HC-PL94T 94Wh 14.8V High-Power Linking Battery - Gold Mount is compatible with your PAGlink PowerHub, Gold Mount camera plates, and Anton/Bauer Li-Ion chargers. Two or more PAGlink batteries, in any state of charge, can be linked to combine their capacities and enable a higher current to be drawn. Up to 12A can be supplied for power-hungry camera configurations with multiple accessories.

Individual PAGlink batteries are capable of 10A alone. (2) linked batteries provide longer run-time than (2) single packs used consecutively. PAGlink also allows batteries to be hot-swapped for continuous power. Linking (2) HC-PL94T packs creates an 188Wh battery.

PAGlink batteries are UN certified and feature exceptional safety features.

Typically, up to (4) PAGlink batteries can be linked for charging on each position of Anton/Bauer Li-Ion chargers, resulting in a 16-channel unit. PAGlink batteries display their individual status during charging. PAGlink allows up to (8) batteries to be linked for charge or discharge. Linked charging was developed by PAG and is unique to the PAGlink system. The result is less battery swapping and fewer chargers required. 

The PAGlink HC-PL94T battery incorporates a convenient numeric display that, with (2) button presses (under load), shows remaining camera run-time in hours and minutes. The display maintains accuracy by tracking cell-performance and adjusting calibration values to compensate for cell-aging. When batteries are linked, the run-time figure is for the entire stack, but a single button press shows individual battery capacity as a percentage.

Features: 

• Battery Mount Type: Gold Mount (3-stud)
• Compatible with optional Gold Mount/Snap-On camera plate, PAGlink PowerHub, and Anton/Bauer Lithium Ion chargers
• Smaller, lighter Li-Ion batteries with a higher energy density
• Draw up to 12A for high-current applications (10A individually)
• Combine capacities for longer run-times
• Hot-swap for continuous power
• Charge batteries linked, using optional Anton/Bauer Li-Ion chargers
• Camera run-time is displayed numerically, in hours and minutes
• Remaining capacity is displayed automatically in the viewfinder/LCD (on compatible cameras)
• Battery firmware can be updated easily in the field
• Intelligent batteries communicate and manage their own charge and discharge, safely

IMPORTANT NOTE: Always check current air travel/transport regulations for Lithium Ion batteries prior to travel.

PAGlink PowerHub

The PAGlink PowerHub is a compact and user-configurable camera accessory power device. It is designed for use with the PAGlink Gold Mount system of intelligent linking batteries.* This breakout box will help you save time on set due to its hot swapping capabilities.

The PAGlink battery system is designed for high-load camera set-ups. The linked batteries provide up to 12A, enabling you to simultaneously power the camera and multiple 12V accessories, such as a camera light, a monitor, audio and transmission devices. The PowerHub provides the multiple outputs required for this purpose.

PowerHub incorporates (5) output ports that accept a range of interchangeable, plug-in connectors. (4) D-Tap connectors are supplied as standard. A USB connector (5V, 1A) is also included, which allows you to charge your smartphone or power similar low-voltage devices. These connectors are interchangeable with Lemo (2-pin), Hirose (4 pin) or 2.1mm (PP90) connectors, available as a separate purchase, and can be used in any of the (5) power ports. Any combination of connectors is possible. This means you can configure the PowerHub to your exact requirements.

The ultra-compact and lightweight PowerHub is designed to be used sandwiched between your (2) PAGlink batteries. This increases the depth of the battery stack by only 12mm. Utilizing (2) batteries will enable the rear battery to be hot-swapped without disconnecting your accessories. When plugged into the built-in D-Tap found on other manufacturer's batteries, you would need to disconnect your accessories. Therefore, the PAGlink PowerHub saves you time. Alternatively, the PowerHub can be connected to rear battery of the stack.

Features:

• Power more 12V camera accessories, using PAGlink Gold Mount batteries
• Sandwich the PowerHub between PAGlink batteries to maintain their hot-swap capability
• Includes (4) D-Tap outputs for 12V camera accessories
• Includes (1) USB connector(5V, 1A) for charging low voltage devices, like your mobile phone
• Other output connector types available for purchase separately, in case you want to swap in other connctors
• Size: 3.5 x 4.48 x 0.98" (89 x 114 x 25mm)
• Weight: 0.27 lb (125 g)

* NOTE: The PowerHub Model 9712 can only be used with PAGlink Gold Mount batteries (Models 9306 and 9313). It draws power from the PAGlink contacts on the face of the battery. It cannot be connected directly to the camera or used with non-linking Gold Mount batteries.

IMPORTANT NOTE: Available via ground or expedited shipping on domestic orders. Please consider picking up this item in-store, as well. Only ships within the United States due to airline restrictions.