AbelCine Wooden Camera RED DSMC2 Accessory Bundle with Pass Through Top Plate - V-Mount

This bundle includes the following items for your RED DSMC2 Camera:

The Wooden Camera Pass Through Top Plate for WEAPON/SCARLET-W/EPIC-W/RAVEN features a 26-pin LCD connection and 3-pin trigger handle interface. It offers arrays of 1/4-20 holes in RED spacing, 3/8-16 holes for large accessories, and the ARRI standard accessory mount in several places. Attach the Pass Through Top Plate to top of camera by (4) 1/4-20 captured screws. 

This product adds mounting points to your DSMC2 camera and allows for other cage and cable components like the optional Safety NATO Arm (WEAPON/SCARLET-W/RAVEN) and optional RED Male Pogo to Female Pogo LCD/EVF Cables to be attached.

The Wooden Camera LW 15mm Bracket (Weapon/Epic-W/Scarlet-W/Raven) combines with the Wooden Camera Easy Riser for Weapon/Epic-W/Scarlet-W/Raven (sold separately) to enable use of lightweight 15mm rods at the correct lens height on RED WEAPON, EPIC-W, SCARLET-W, RAVEN, and other DSMC2 cameras.

Specifications:

• Weight: 0.3 lb (136 g)
• Dimensions: 1" x 5" x 1" (25.4mm x 127mm x 25.4mm)
• Includes: (2) 1/4"-20 captured screws

The Wooden Camera AIR EVF Mount for RED DSMC2 EVF is an ultra-lightweight EVF mount that enables easy positioning of the RED DSMC2 viewfinder (not included). The system travels forward and backward over the lens area on two 15mm rods, and laterally (left and right) on a single 19mm rod. A friction knuckle enables quick tilt adjustment of the EVF without needing to loosen a thumbscrew. The knuckle's thin design allows for both straight and right angle LEMO compatible connectors to be installed into the EVF.

When paired with the Wooden Camera Easy Top (DSMC2), an LCD/EVF Cable (RED, R/R, 24") is an ideal choice, as it provides sufficient length for adequate positioning in most configurations. If using the AIR EVF Mount without the Easy Top, a Male Pogo To Male LEMO Compatible LCD/EVF Cable (24") would be recommended.

NOTE: Camera, EVF, plates, cables, and other accessories sold separately.

A top 15mm lightweight rod mount is required for proper attachment of the AIR EVF Mount, and the Master Top Handle (shown in the example photos) is an excellent option for this. Alternatively, if you already have the NATO Handle Kit (Plus, 100mm) or similar, a Rod Clamp (15mm LW) can be added to the front, which would hold the two 15mm rods. Please contact an AbelCine salesperson if you require any configuration assistance.

The tool-free design permits quick installation and removal of the EVF, and if further extension is needed for tripod shooting, the AIR EVF Extension Arm (RED DSMC2 EVF) can be installed using the same method.

This Wooden Camera Easy Riser, a riser shim plate, delivers corrected lens height. Combine this Easy Riser with an optional Wooden Camera Bridgeplate (19mm or 15mm Studio), or an optional Wooden Camera LW 15mm Bracket (Weapon), or other optional RED-style bridgeplate to adjust lens height.

The Easy Riser includes (2) captured 3/8"-16 screws and multiple mounting points.

Camera Compatibility:

• RED EPIC-W
• RED SCARLET-W
• RED RAVEN
• RED WEAPON

This riser is also compatible with the original Wooden Camera LW 15mm Bracket for RED EPIC/SCARLET, though the footprint now matches the newer WEAPON models.

The Wooden Camera Cableless V-Mount for RED WEAPON / SCARLET-W / RAVEN is a cable-free, V-Mount battery plate system designed for use with RED WEAPON, EPIC WEAPON (EPIC-W), SCARLET WEAPON (SCARLET-W), and RAVEN cameras.

This system utilizes an IDX brand battery plate with (2) P-Tap ports and the Wooden Camera pogo interface module. The assembly attaches without tools, directly to the back of the RED camera, Base Expander Module, REDVolt Expander Module, and some third party modules (such as OMODs).

This system can be configured in center, high, and low modes. Center mode is most appropriate for regular use. High mode is where the battery plate sits above the back of the camera. Low mode is where the plate is configured to be flush with the top of the camera body, leaving batteries in a very compact configuration. The RED DSMC2 top handle will clear RED Brick batteries when the Cableless V-Mount plate is configured in Low mode.

The Cableless V-Mount will communicate charge percentage or voltage data to the camera's LCD display. Intelligent batteries like RED Bricks, Blueshape, Switronix, PAG, and other batteries utilizing SMBUS or reversed SMBUS will allow for the module to communicate percentage data and estimated run time. Non-SMBUS batteries like some IDX and other low cost batteries will only provide voltage data to the camera through the Wooden Camera module.

IMPORTANT NOTE: When using Cableless and D-Box battery modules it is important to know the amount of power your batteries are capable of providing. A RED Brick battery can supply up to 10A, with the camera generally consuming 4-6A in standard configuration.

Although the remaining power is available from the P-Tap, LEMO compatible, Fischer connectors, etc., it is best to limit the power draw to 4A or less for best results. Consuming more power than a battery is capable of providing will cause the battery to shut down.

Specifications:

• Battery Mount: IDX V-Mount
• Weight: 1 lb (453.6 g)
• Dimensions: 5.5" x 1.3" x 3.3" (142mm x 33mm x 85mm)

NOTE: Connectors used in this assembly are not manufactured by LEMO but are made to the same specifications and are LEMO compatible.

The Wooden Camera Trigger Handle for RED WEAPON / SCARLET-W / RAVEN attaches (without tools) directly to the top of the camera brain or to the Easy Top for WEAPON/EPIC-W/SCARLET-W/RAVEN to trigger the camera through the pogo interface. Features arrays of 1/4"-20 female threads in RED spacing, 3/8"-16 female threads for large accessories, and ARRI standard accessory mounts in several places. Attaches to top of camera via (2) 1/4"-20 captured thumbscrews (included). Additionally, Rod Clamps (sold separately) can be attached to the front for a pass-through top rod system.

IMPORTANT NOTE: There is not enough clearance on the top of the camera body to accommodate both the Tool-less LCD/EVF Adapter and the Trigger Handle in place at the same time. Wooden Camera is currently investigating alternate methods to achieve compatibility between these two products.

The Lightweight 15mm Rod Clamp from Wooden Camera provides 1/4-20 mounting points on existing 15mm rods. It can be turned over and bolted to cheeseplates, cages, battery plates, and more. 

Includes:
(2) 1/4-20 x 1/4" screws
(2) 1/4-20 x 3/4" screws

The Wooden Camera 15mm Rod - 6" is a 15mm diameter iris rod used for mounting a follow focus, mattebox, lens support, servo motor(s), and other accessories.

Features:

• Rod Diameter: 15mm
• Length: 6"
• Weight: 0.16 lb (72 g) 

NOTE: Camera and unlisted accessories sold separately.